Pre Made Volume Fans

Customisable Volume. Effortless Luxury.

From soft dimension to bold, full glam, premade volume fans allow you to tailor every set. Lightweight yet fluffy, each fan is perfectly symmetrical for consistent, statement-making results.

Discover

Pre Made Volume Fans

$9.95 Delivery - Over $150 Free Shipping Australia Wide.

Lightweight - Comfortable - Vegan - Easy To Apply.

DIY LASH EXTENSIONS

EASY TO APPLY WITH A LUXURIOUS FINISH

STEP 1

Prepare Your Natural Lashes
- Start with clean, dry lashes.
- Remove all makeup, oils, and residue from your lash line.
- Brush through your natural lashes with a clean spoolie.
STEP 2

Apply Kave Bonder
- Using the applicator wand, apply a thin layer of Kave DIY Bond to the underside of your natural lashes, focusing on the base where the lash clusters will be attached.
- Work in sections rather than coating the entire lash line at once.
- Allow the bond to become slightly tacky for 20–30 seconds before applying clusters.
STEP 3

Apply Kave Lash Clusters
- Using lash applicator tweezers, gently pick up a lash cluster.
- Place the cluster underneath your natural lashes, approximately 1–2mm away from the waterline.
- Start from the outer corner and work your way inward, or apply according to your preferred mapping style.
- Continue applying clusters until your desired look is achieved.
STEP 4

Fuse The Lashes
- Once all clusters are in place, use your lash applicator to gently squeeze the clusters and natural lashes together.
- This helps secure the bond and creates a seamless finish.
STEP 5

Apply DIY Sealer

Wait 60 seconds then start sealer process. This allows the adhesive to set slightly so it doesn’t smudge or clump when the sealer hits it.

Kave's Easy DIY Instructions

Last Steps & Care Instructions - Apply Kave Searler

Last Step After Letting Bond Dry Slightly

Step 1 Wait 30–60 Seconds After Applying Bond.

After pressing your cluster lashes onto your natural lashes using your bond, Then apply the sealer. This allows the adhesive to set slightly so it doesn’t smudge or clump when the sealer hits it.

Step 2: Scrape Off The Excess Product

Crucial for a clean look.
Open your sealer and scrape the wand against the rim of the tube. You want a very minimal amount of product on the brush. Using too much sealer is the number one cause of crunchy, white, or flaky lashes.

Step 3: Dab Only At The Base

Avoid the tips.
Gently dab or swipe the sealer only along the very base of the lash clusters—right where you applied the bond. Do not brush it all the way through to the tips of the lashes like mascara, or they will clump together and lose their fluffy look.

Step 4: Do the final fuse

Lock them in place.
Take your lash applicator/tweezer tool and wipe it completely clean so there is no residual glue on it. Gently squeeze the base of the clusters and your natural lashes together one final time. This fuses the bond, natural lash, and sealer perfectly together.

💡 Two Quick Tips for Better Retention:

The Applicator Trick: If you are worried about getting sealer on the lash tips, you can actually scrape a little sealer directly onto the tips of your lash applicator tool, and then pinch the base of your lashes with it. This seals and fuses them at the exact same time!
Avoid Water for 24 Hours: Even though the sealer cures the bond instantly, it's best practice to keep them completely dry for the first 24 hours to let the adhesive fully set.

Aftercare Tips

Avoid getting lashes wet for the first 4–6 hours after application.
Avoid oil-based cleansers and skincare products around the eye area.
Do not rub or pull on your lash clusters.
Store your lash products in a cool, dry place with lids securely closed.

Pro Tip: Less is more. Applying a thin layer of both bond and bonder will give you the best retention and the most natural-looking finish.

Estimated Wear Time: 5–10 days with proper application and aftercare.

Kave Lashes – Professional Results, Made Simple.

Discover